The Hunter 38
is a 36’8” (11.18m) cruising sailboat designed by Glenn Henderson
(United States). She was built since 2004 (and now discontinued) by Marlow Hunter
(United States). The Deep draft
version displays a deeper fin allowing a lower center of gravity and extra performance especially upwind.
The Hunter 38
is as well listed, on Boat-Specs.com, in Shoal draft
and Furling mainsail
version (see all the versions compared
Hunter 38's main features
Hull and deck: GRP (glass reinforced polyester)
First built hull
Last built hull
Keel : fin without bulb
Single helm wheel
Single spade rudder
EC design category iThe CE design category indicates the ability to cope with certain weather conditions (the sailboat is designed for these conditions)
A: Wind < force 9, Waves < 10m
B: Wind < force 8, Waves < 8m
C: Wind < force 6, Waves < 4m
D: Wind < force 4, Waves < 0,5m
Standard public price ex. VAT (indicative only)
Hunter 38's main dimensions
38’ 2”11.63 m
36’ 8”11.18 m
34’ 8”10.57 m
12’ 11”3.94 m
6’ 6”1.98 m
Mast height from DWL
59’ 1”18.01 m
Light displacement (MLC)
18365 lb8330 kg
6574 lb2982 kg
Hunter 38's rig and sails
Upwind sail area
991 ft²92.07 m²
I iFore triangle height (from mast foot to fore stay top attachment)
46’ 8”14.22 m
J iFore triangle base (from mast foot to bottom of forestay)
12’ 1”3.68 m
P iMainsail hoist measurement (from tack to head)
47’ 5”14.45 m
E iMainsail foot measurement (from tack to clew)
17’ 8”5.41 m
Sloop Marconi fractional
Deck stepped mast
Number of levels of spreaders
1x19 strand wire discontinuous
Hunter 38's performances
Upwind sail area to displacement iThe ratio sail area to displacement is obtained by dividing the sail area by the boat's displaced volume to the power two-thirds.
The ratio sail area to displacement can be used to compare the relative sail plan of different sailboats no matter what their size.
Upwind: under 18 the ratio indicates a cruise oriented sailboat with limited performances especially in light wind, while over 25 it indicates a fast sailboat.
241 ft²/T22.41 m²/T
Displacement-length ratio (DLR) iThe Displacement Length Ratio (DLR) is a figure that points out the boat's weight compared to its waterline length. The DLR is obtained by dividing the boat's displacement in tons by the cube of one one-hundredth of the waterline length (in feet).
The DLR can be used to compare the relative mass of different sailboats no matter what their length:
a DLR less than 180 is indicative of a really light sailboat (race boat made for planning), while a DLR greater than 300 is indicative of a heavy cruising sailboat.
Ballast ratio iThe Ballast ratio is an indicator of stability; it is obtained by dividing the boat's displacement by the mass of the ballast. Since the stability depends also of the hull shapes and the position of the center of gravity, only the boats with similar ballast arrangements and hull shapes should be compared.
The higher the ballast ratio is, the greater is the stability.
Critical hull speed iAs a ship moves in the water, it creates standing waves that oppose its movement. This effect increases dramatically the resistance when the boat reaches a speed-length ratio (speed-length ratio is the ratio between the speed in knots and the square root of the waterline length in feet) of about 1.2 (corresponding to a Froude Number of 0.35) . This very sharp rise in resistance, between speed-length ratio of 1.2 to 1.5, is insurmountable for heavy sailboats and so becomes an apparent barrier. This leads to the concept of "hull speed".
The hull speed is obtained by multiplying the square root of the waterline length (in feet) by 1.34.
Hunter 38's auxiliary engine
1 inboard engine
Engine(s) power (min./max.)
29 HP / 40 HP
Fuel tank capacity
34.9 gal132 liters
Hunter 38's accommodations and layout
Open aft cockpit
2 / 3
4 / 8
Freshwater tank capacity
75 gal284 liters
Holding tank capacity
34.1 gal129 liters
5 gal19 liters
6’ 6”1.98 m
Have you spotted incorrect data? You can report it in the forum
or contact the webmaster